Fraxinus00tw assembly manual

Slide 1

Slide 1 text

Fraxinus Fast × Cute × Compact CoreXY 3D Printer フラクシネス 00tw

Slide 2

Slide 2 text

Open!

Slide 3

Slide 3 text

No content

Slide 4

Slide 4 text

introduction

Slide 5

Slide 5 text

wiring diagram Raspberry Pi Zero 2W motor E 5015 fan R motor B motor A motor Z 5015 fan L bed heater bed thermistor hot end thermistor (optional) IR Probe 3010 hot end fan OUT GND VCC hot end Bambu x1c v2.0 (optional) heater bed SKR PICO V1.0 V+ GND USB-PD trigger

Slide 6

Slide 6 text

Raspberry Pi Zero 2W wiring diagram SKR PICO V1.0 0.96”OLED (I2C) rotary encoder (optional) ADXL345 configuration: [display] lcd_type: ssd1306 menu_timeout: 30 i2c_mcu: host i2c_bus: i2c.1 i2c_address: 60 #(0x3c) encoder_pins: host:gpio17, host:gpio27 click_pin: ^!host:gpio22 configuration: [adxl345] cs_pin: host:None spi_bus:spidev0.0 [resonance_tester] accel_chip: adxl345 probe_points: 35, 35, 20 max_freq: 133.33 GND VCC SCL SDA CLK DT SW ✙ GND

Slide 7

Slide 7 text

frame assembly

Slide 8

Slide 8 text

frame assembly hex nut M3 （17pcs） hex nut M3 （17pcs） panel side R panel side L

Slide 9

Slide 9 text

hex nut M3 （17pcs） panel back (sherpa mini / HGX-Lite) panel bottom frame assembly

Slide 10

Slide 10 text

panel side L M3x10 button bolt (6pcs) panel back (sherpa mini / HGX-Lite) M3x10 flat head bolt (6pcs) panel middle panel side R frame assembly

Slide 11

Slide 11 text

drive system assembly

Slide 12

Slide 12 text

M3x8 button bolt (10pcs) linear rail MGN9C 100mm (2pcs) M3x8 flat head bolt (3pcs) M3x12 flat head bolt (2pcs) plate stopper z plate stopper z drive system assembly

Slide 13

Slide 13 text

extruder (sherpa mini) motor NEMA11 B panel back (sherpa mini) motor NEMA11 A M3x12 button bolt (2pcs) motor NEMA11 Z bulb PC4-HS drive system assembly (sherpa mini extruder)

Slide 14

Slide 14 text

extruder (HGX-Lite) motor NEMA11 B panel back (HGX-Lite) M3x12 button bolt (2pcs) motor NEMA11 Z bulb PC4-HS drive system assembly (HGX-Lite extruder) motor NEMA11 A

Slide 15

Slide 15 text

M3x10 button bolt M2.5x8 screw (12pcs) motor NEMA11 Z motor NEMA11 A motor NEMA11 B washer M3x6x0.5 (5pcs) bearing V623ZZ washer M3x6x0.5 drive system assembly

Slide 16

Slide 16 text

hex nut M2 1.2mmt reel f00w M3x4 socket set screw M2x8 screw hex nut M3 (3pcs for A, B, Z motor) drive system assembly M2x8 screw hex nut M2 1.2mmt

Slide 17

Slide 17 text

drive system assembly (wire installation)

Slide 18

Slide 18 text

M3x10 button bolt(10pcs) linear rail MGN9C 100mm (2pcs) reel f00 Z wire Z drive system assembly

Slide 19

Slide 19 text

drive system assembly M3x8 button bolt (11pcs) hex nut M3 （11pcs） plate x-carriage linear rail MGN9C 100mm

Slide 20

Slide 20 text

drive system assembly washer M3x6x0.5 (8pcs) bearing V623ZZ (4pcs) plate carriage R Spacer 3.2-6 x5mmt (8pcs) plate x-carriage M3x16 button bolt (6pcs) plate carriage L (x-carriage L) (x-carriage R)

Slide 21

Slide 21 text

drive system assembly washer M3x6x0.5 (8pcs) bearing V623ZZ (4pcs) Spacer 3.2-6 x5mmt (2pcs) M3x20 button bolt (3pcs) frame top L

Slide 22

Slide 22 text

drive system assembly washer M3x6x0.5 (8pcs) bearing V623ZZ (4pcs) Spacer 3.2-6 x5mmt (2pcs) M3x20 button bolt (3pcs) frame top R

Slide 23

Slide 23 text

drive system assembly M3x8 button bolt (4pcs) holder mgn9c hex nut M3 （2pcs） MGN9C Carriage

Slide 24

Slide 24 text

drive system assembly reel f00 A wire A hex nut M3 （4pcs）

Slide 25

Slide 25 text

drive system assembly reel f00 B wire B hex nut M3 （4pcs）

Slide 26

Slide 26 text

print system assembly

Slide 27

Slide 27 text

acrylic plate clear 90x90x3 fan mount R panel side R print system assembly duct side fan 5015 (normal / narrow) fan 5015 M3x10 button bolt (2pcs)

Slide 28

Slide 28 text

acrylic plate clear 90x90x3 fan mount L panel side L print system assembly duct side fan 5015 (normal / narrow) fan 5015 M3x10 button bolt (2pcs)

Slide 29

Slide 29 text

print system assembly M3x8 button bolt (2pcs) holder head-wire (normal / IR sensor) M3x14 button bolt (2pcs) 3010 fan (optional) IR sensor (optional) M2.5x6 screw (2pcs) M3x18 cap bolt (2pcs) M3x6 button bolt (2pcs) bulb PC4-HS hex nut M3 （4pcs） hot end bambu x1c (compatible v2.0) holder mgn9c （plate x-carriage)

Slide 30

Slide 30 text

bed frame(normal / heated) print system assembly M3x12 cap bolt (2pcs) (optional) Limit switch KP3S hex nut M3 holder switch (optional) M3x12 cap bolt (2pcs)

Slide 31

Slide 31 text

frame heatbed print system assembly M3x20 flat head bolt (3pcs) adjust knob (3pcs) hex nut M3 (6pcs) spacer nut (3pcs) spring conical φ6-10-1.2-10mm (3pcs) film heater 25x50mm (2pcs) bed thermistor heating plate (80x80x3mm) build plate (80x80x1mm) (heated bed)

Slide 32

Slide 32 text

frame bed print system assembly M3x20 flat head bolt (3pcs) adjust knob (3pcs) hex nut M3 (6pcs) spacer nut (3pcs) spring conical φ6-10-1.2-10mm (3pcs) plate bed (80x80x5mm) (normal bed)

Slide 33

Slide 33 text

bed (normal / heated) print system assembly washer M3x8x0.5 M3x12 button bolt (8pcs) M3x12 button bolt

Slide 34

Slide 34 text

Bowden tube print system assembly M3x12 flat head bolt (2pcs) hex nut M3 plate back sub (sherpa) (sherpa mini extruder)

Slide 35

Slide 35 text

Bowden tube print system assembly M3x18 flat head bolt (2pcs) hex nut M3 plate back sub (HGX-Lite) (HGX-Lite extruder)

Slide 36

Slide 36 text

control system assembly

Slide 37

Slide 37 text

Raspberry Pi Zero 2W control system assembly holder skr-pico f00 SKR PICO V1.0 DPDT SW（IS-2235） M2x6 screw (8pcs) pin header(2x20 right angled)

Slide 38

Slide 38 text

Raspberry Pi Zero 2W holder skr-pico f00 SKR PICO V1.0 panel bottom M3x6 button bolt (4pcs) hex nut M3 （4pcs） control system assembly

Slide 39

Slide 39 text

holder skr-pico f00 panel bottom M3x12 flat head bolt (4pcs) control system assembly

Slide 40

Slide 40 text

panel control (DPDT SW) magnet 6x3mm (2pcs) knob R DPDT Toggle Switch rotary encoder control system assembly knob L (DPDT SW) guide switch a guide switch b M2.5x5 screw (10pcs) 0.96“ OLED display OLED mount (control panel : DPDT SW)

Slide 41

Slide 41 text

DPDT Toggle Switch (GND) control system assembly (control panel : DPDT SW - wiring) (V+) USB-PD trigger (20V) USB-PD trigger (15V) SKR PICO V1.0

Slide 42

Slide 42 text

control system assembly (control panel : PWM) panel control (PWM) magnet 6x3mm (2pcs) knob R rotary encoder knob L (PWM) PWM controller M2.5x5 screw (10pcs) 0.96“ OLED display OLED mount

Slide 43

Slide 43 text

frame bottom panel bottom panel control (DPDT SW / PWM) control system assembly hex nut M3 （2pcs） magnet 6x3mm (2pcs) M3x10 flat head bolt (2pcs)

Slide 44

Slide 44 text

door panel assembly

Slide 45

Slide 45 text

acrylic plate clear 110x130x3 plate door inner plate door base door panel assembly hex nut M3 （2pcs） magnet 6x3mm (3pcs) M3x6 button bolt (4pcs) handle（2pcs） handle base（2pcs） filament 1.75x6mm（5pcs） M3x12 cap bolt (2pcs)

Slide 46

Slide 46 text

frame upper door arm (2pcs) door panel assembly M3x8 cap bolt (2pcs)

Slide 47

Slide 47 text

frame upper door panel assembly M3x14 cap bolt (6pcs) frame bottom magnet 6x3mm (3pcs)

Slide 48

Slide 48 text

frame upper door panel assembly M3x12 button bolt (2pcs) M3x12 flat head bolt (2pcs) spacer (2pcs)

Slide 49

Slide 49 text

top hat assembly

Slide 50

Slide 50 text

Plate top base hex nut M3 (6pcs) top hat assembly M3x6 button bolt (4pcs) acrylic plate clear 110x110x3 Plate top inner

Slide 51

Slide 51 text

plate back sub hex nut M3 (6pcs) top hat assembly M3x6 button bolt (2pcs) knob b (2pcs) plate back acrylic plate clear 110x45x3 M3x14 button bolt (2pcs) knob a (2pcs) knob c (2pcs)

Slide 52

Slide 52 text

panel back M3x14 button bolt (4pcs) top hat assembly M3x8 button bolt (4pcs) plate left plate right 4mm

Slide 53

Slide 53 text

panel top M3x10 button bolt (4pcs) top hat assembly M3x8 button bolt (2pcs) plate left panel back plate left

Slide 54

Slide 54 text

top hat top hat assembly Locking knob

Slide 55

Slide 55 text

exterior assembly

Slide 56

Slide 56 text

foot corn base (4pcs) exterior assembly M3x12 cap bolt(4pcs) panel bottom foot corn inner (4pcs) (corn foot)

Slide 57

Slide 57 text

foot pillar (4pcs) M3x12 cap bolt (4pcs) panel bottom (pillar foot) exterior assembly

Slide 58

Slide 58 text

filament inlet PD module mounter panel bottom exterior assembly USB-PD trigger tube inlet bulb PC4-HS (optional) power bank (Cheergo T108LF)

Slide 59

Slide 59 text

plate grid (sherpa / HGX-Lite) clip (2pcs) exterior assembly M3x10 button bolt (4pcs) 4mm