Fraxinus00tw assembly manual

The first edition of the assembly manual for the micro 3D printer “Fraxinus00tw” created by SummerOrange has been completed. With the creator’s permission, we are publishing it here.

Reference URL:
https://x.com/Fukumay1/status/1884396047113543918
https://fraxinus.jp/

Transcript

1. Fraxinus Fast × Cute × Compact CoreXY 3D Printer フ ラ ク シ ネ ス 00tw
2. Open!
4. introduction
5. wiring diagram Raspberry Pi Zero 2W motor E 5015 fan R motor B motor A motor Z 5015 fan L bed heater bed thermistor hot end thermistor (optional) IR Probe 3010 hot end fan OUT GND VCC hot end Bambu x1c v2.0 (optional) heater bed SKR PICO V1.0 V+ GND USB-PD trigger
6. Raspberry Pi Zero 2W wiring diagram SKR PICO V1.0 0.96”OLED (I2C) rotary encoder (optional) ADXL345 configuration: [display] lcd_type: ssd1306 menu_timeout: 30 i2c_mcu: host i2c_bus: i2c.1 i2c_address: 60 #(0x3c) encoder_pins: host:gpio17, host:gpio27 click_pin: ^!host:gpio22 configuration: [adxl345] cs_pin: host:None spi_bus:spidev0.0 [resonance_tester] accel_chip: adxl345 probe_points: 35, 35, 20 max_freq: 133.33 GND VCC SCL SDA CLK DT SW ✙ GND
7. frame assembly
8. frame assembly hex nut M3 （17pcs） hex nut M3 （17pcs） panel side R panel side L
9. hex nut M3 （17pcs） panel back (sherpa mini / HGX-Lite) panel bottom frame assembly
10. panel side L M3x10 button bolt (6pcs) panel back (sherpa mini / HGX-Lite) M3x10 flat head bolt (6pcs) panel middle panel side R frame assembly
11. drive system assembly
12. M3x8 button bolt (10pcs) linear rail MGN9C 100mm (2pcs) M3x8 flat head bolt (3pcs) M3x12 flat head bolt (2pcs) plate stopper z plate stopper z drive system assembly
13. extruder (sherpa mini) motor NEMA11 B panel back (sherpa mini) motor NEMA11 A M3x12 button bolt (2pcs) motor NEMA11 Z bulb PC4-HS drive system assembly (sherpa mini extruder)
14. extruder (HGX-Lite) motor NEMA11 B panel back (HGX-Lite) M3x12 button bolt (2pcs) motor NEMA11 Z bulb PC4-HS drive system assembly (HGX-Lite extruder) motor NEMA11 A
15. M3x10 button bolt M2.5x8 screw (12pcs) motor NEMA11 Z motor NEMA11 A motor NEMA11 B washer M3x6x0.5 (5pcs) bearing V623ZZ washer M3x6x0.5 drive system assembly
16. hex nut M2 1.2mmt reel f00w M3x4 socket set screw M2x8 screw hex nut M3 (3pcs for A, B, Z motor) drive system assembly M2x8 screw hex nut M2 1.2mmt
17. drive system assembly (wire installation)
18. M3x10 button bolt(10pcs) linear rail MGN9C 100mm (2pcs) reel f00 Z wire Z drive system assembly
19. drive system assembly M3x8 button bolt (11pcs) hex nut M3 （11pcs） plate x-carriage linear rail MGN9C 100mm
20. drive system assembly washer M3x6x0.5 (8pcs) bearing V623ZZ (4pcs) plate carriage R Spacer 3.2-6 x5mmt (8pcs) plate x-carriage M3x16 button bolt (6pcs) plate carriage L (x-carriage L) (x-carriage R)
21. drive system assembly washer M3x6x0.5 (8pcs) bearing V623ZZ (4pcs) Spacer 3.2-6 x5mmt (2pcs) M3x20 button bolt (3pcs) frame top L
22. drive system assembly washer M3x6x0.5 (8pcs) bearing V623ZZ (4pcs) Spacer 3.2-6 x5mmt (2pcs) M3x20 button bolt (3pcs) frame top R
23. drive system assembly M3x8 button bolt (4pcs) holder mgn9c hex nut M3 （2pcs） MGN9C Carriage
24. drive system assembly reel f00 A wire A hex nut M3 （4pcs）
25. drive system assembly reel f00 B wire B hex nut M3 （4pcs）
26. print system assembly
27. acrylic plate clear 90x90x3 fan mount R panel side R print system assembly duct side fan 5015 (normal / narrow) fan 5015 M3x10 button bolt (2pcs)
28. acrylic plate clear 90x90x3 fan mount L panel side L print system assembly duct side fan 5015 (normal / narrow) fan 5015 M3x10 button bolt (2pcs)
29. print system assembly M3x8 button bolt (2pcs) holder head-wire (normal / IR sensor) M3x14 button bolt (2pcs) 3010 fan (optional) IR sensor (optional) M2.5x6 screw (2pcs) M3x18 cap bolt (2pcs) M3x6 button bolt (2pcs) bulb PC4-HS hex nut M3 （4pcs） hot end bambu x1c (compatible v2.0) holder mgn9c （plate x-carriage)
30. bed frame(normal / heated) print system assembly M3x12 cap bolt (2pcs) (optional) Limit switch KP3S hex nut M3 holder switch (optional) M3x12 cap bolt (2pcs)
31. frame heatbed print system assembly M3x20 flat head bolt (3pcs) adjust knob (3pcs) hex nut M3 (6pcs) spacer nut (3pcs) spring conical φ6-10-1.2-10mm (3pcs) film heater 25x50mm (2pcs) bed thermistor heating plate (80x80x3mm) build plate (80x80x1mm) (heated bed)
32. frame bed print system assembly M3x20 flat head bolt (3pcs) adjust knob (3pcs) hex nut M3 (6pcs) spacer nut (3pcs) spring conical φ6-10-1.2-10mm (3pcs) plate bed (80x80x5mm) (normal bed)
33. bed (normal / heated) print system assembly washer M3x8x0.5 M3x12 button bolt (8pcs) M3x12 button bolt
34. Bowden tube print system assembly M3x12 flat head bolt (2pcs) hex nut M3 plate back sub (sherpa) (sherpa mini extruder)
35. Bowden tube print system assembly M3x18 flat head bolt (2pcs) hex nut M3 plate back sub (HGX-Lite) (HGX-Lite extruder)
36. control system assembly
37. Raspberry Pi Zero 2W control system assembly holder skr-pico f00 SKR PICO V1.0 DPDT SW（IS-2235） M2x6 screw (8pcs) pin header(2x20 right angled)
38. Raspberry Pi Zero 2W holder skr-pico f00 SKR PICO V1.0 panel bottom M3x6 button bolt (4pcs) hex nut M3 （4pcs） control system assembly
39. holder skr-pico f00 panel bottom M3x12 flat head bolt (4pcs) control system assembly
40. panel control (DPDT SW) magnet 6x3mm (2pcs) knob R DPDT Toggle Switch rotary encoder control system assembly knob L (DPDT SW) guide switch a guide switch b M2.5x5 screw (10pcs) 0.96“ OLED display OLED mount (control panel : DPDT SW)
41. DPDT Toggle Switch (GND) control system assembly (control panel : DPDT SW - wiring) (V+) USB-PD trigger (20V) USB-PD trigger (15V) SKR PICO V1.0
42. control system assembly (control panel : PWM) panel control (PWM) magnet 6x3mm (2pcs) knob R rotary encoder knob L (PWM) PWM controller M2.5x5 screw (10pcs) 0.96“ OLED display OLED mount
43. frame bottom panel bottom panel control (DPDT SW / PWM) control system assembly hex nut M3 （2pcs） magnet 6x3mm (2pcs) M3x10 flat head bolt (2pcs)
44. door panel assembly
45. acrylic plate clear 110x130x3 plate door inner plate door base door panel assembly hex nut M3 （2pcs） magnet 6x3mm (3pcs) M3x6 button bolt (4pcs) handle（2pcs） handle base（2pcs） filament 1.75x6mm（5pcs） M3x12 cap bolt (2pcs)
46. frame upper door arm (2pcs) door panel assembly M3x8 cap bolt (2pcs)
47. frame upper door panel assembly M3x14 cap bolt (6pcs) frame bottom magnet 6x3mm (3pcs)
48. frame upper door panel assembly M3x12 button bolt (2pcs) M3x12 flat head bolt (2pcs) spacer (2pcs)
49. top hat assembly
50. Plate top base hex nut M3 (6pcs) top hat assembly M3x6 button bolt (4pcs) acrylic plate clear 110x110x3 Plate top inner
51. plate back sub hex nut M3 (6pcs) top hat assembly M3x6 button bolt (2pcs) knob b (2pcs) plate back acrylic plate clear 110x45x3 M3x14 button bolt (2pcs) knob a (2pcs) knob c (2pcs)
52. panel back M3x14 button bolt (4pcs) top hat assembly M3x8 button bolt (4pcs) plate left plate right 4mm
53. panel top M3x10 button bolt (4pcs) top hat assembly M3x8 button bolt (2pcs) plate left panel back plate left
54. top hat top hat assembly Locking knob
55. exterior assembly
56. foot corn base (4pcs) exterior assembly M3x12 cap bolt(4pcs) panel bottom foot corn inner (4pcs) (corn foot)
57. foot pillar (4pcs) M3x12 cap bolt (4pcs) panel bottom (pillar foot) exterior assembly
58. filament inlet PD module mounter panel bottom exterior assembly USB-PD trigger tube inlet bulb PC4-HS (optional) power bank (Cheergo T108LF)
59. plate grid (sherpa / HGX-Lite) clip (2pcs) exterior assembly M3x10 button bolt (4pcs) 4mm